• CSA W117.2-06 (R2011)

CSA W117.2-06 (R2011)

  • standard by CSA Group, 10/01/2006
  • Safety in Welding, Cutting and Allied Processes
  • Category: CSA GROUP

$84.00 $42.00

Full Description

Update #1 was published as notification that this is now a National Standard of Canada.

This PDF includes updates #1 & 2.

Preface

This is the fifth edition of CSA W117.2, Safety in welding, cutting, and allied processes. It supersedes the previous editions published in 2001, 1994, 1987, and 1974. Its subject is the health and safety of welders and welding operators. The safe design of welding equipment is covered in other Standards that are referenced in this document.

1 Scope

1.1 Objective

1.1.1
This Standard provides minimum requirements and recommendations to protect persons who work in an environment affected by welding, cutting, and allied processes from illness and injury, and to prevent damage to property arising from the installation, operation, and maintenance of equipment used in these processes.

1.1.2
This Standard specifies the elements of a welding health and safety program (see Clause 4) that are necessary to implement the requirements and recommendations described in Clause 1.1.1.

1.2 Applicability

1.2.1
This Standard applies to all personnel working in an environment affected by welding, cutting, and allied processes.

1.2.2
The requirements of this Standard apply to the processes illustrated in the Master chart of welding and allied processes (see Figure A.1).

1.2.3
Where a conflict arises between a requirement in this Standard and the legislative requirements of a provincial or federal jurisdiction, the legislative requirements prevail.

1.3 Exclusions

This Standard does not apply to the design or manufacture of welding or safety equipment.

1.4 Terminology

In CSA Standards, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; "may" is used to express an option or that which is permissible within the limits of the standard; and "can" is used to express possibility or capability. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Product Details

Edition:
5th
Published:
10/01/2006
ISBN(s):
1554361915
Number of Pages:
122
File Size:
1 file , 2.2 MB
Product Code(s):
2418369, 2019242
Note:
This product is unavailable in Russia, Ukraine, Belarus

Document History

CSA W117.2:19

CSA W117.2-12 (R2017)

CSA W117.2-06 (R2011)

CSA W117.2-94

CSA ANSI Z83.4-2013/CSA 3.7-2013

CSA ANSI Z83.4-2013/CSA 3.7-2013

Non-Recirculating Direct Gas-Fired Industrial Air Heaters..

$221.00 $441.00

CSA C838-13 (R2022)

CSA C838-13 (R2022)

Energy efficiency test methods for three-phase variable frequency drive systems, Includes Update No...

$155.00 $309.00

CSA ANSI Z21.56-2013/CSA 4.7-2013

CSA ANSI Z21.56-2013/CSA 4.7-2013

Gas-Fired Pool Heaters..

$300.00 $599.00

CSA ANSI Z21.93-13/CSA 6.30-13

CSA ANSI Z21.93-13/CSA 6.30-13

Excess flow valves for natural and LP gas with pressures up to 5 psig..

$186.00 $371.00